Before rapier combat at each and every SCA event, including practices, training and pick-ups, a warranted rapier combat marshal must inspect and approve any armor you will use.
For multi-day events, you must have your armor inspected before each day's combat to check for any tears or signs of wearing.
Even though your armor and weapons have been inspected by a marshal, you accept full responsibility for the condition and safety of your equipment.
If you are a combatant on the field during rapier combat activities, you must wear armor that meets or exceeds the minimum standards set in this handbook, and any additional armor requirements of the kingdom you are in.
It is your responsibility to decide if you want to wear any additional armor beyond the minimum standards required, to reduce the risk of combat to an acceptable level to you.
Protection can come from a combination of armor and equipment, but must meet or exceed the minimum standards required.
The areas required to be armored must stay protected during typical movements that you will make during combat.
Your armor must be fastened in a way that prevents it from being dislodged in normal use.
All metal must be free of sharp edges.
You must disguise, cover, or remove modern corporate logos and sport gear unless the gear is necessary for medical reasons. We are trying to maintain the historical atmosphere.
If you have any body-worn medical equipment, you must cover it in such a way that it is protected against blows or the possibility of you falling on it if such an impact could damage it or cause injury.
Summary of areas to be armored
Areas of your body which must be armored are:
Rigid material: Your head and neck, including your face, throat, and your cervical and first thoracic vertebrae. Your cervical vertebrae are the vertebrae in your neck. The first thoracic vertebra is the first major lump which can be felt in the spine at the base of your neck.
Puncture resistant: Your torso, including the inner arm down to 4 inches (10 cm) below the armpit, and your groin area.
If you have testicles, rigid material.
Types of armor
There are three types of armor providing different levels of protection:
Rigid
Penetration resistant
Abrasion resistant
Rigid
Material that will not significantly flex, spread apart, or deform under pressure of 12 kg applied by a standard mask tester, repeatedly to any single point.
Examples of rigid material are:
22 gauge stainless steel (0.8 mm)
20 gauge mild steel (1.0 mm)
16 gauge aluminum, copper, or brass (1.6 mm)
One layer of hardened heavy leather (8 ounce, 3.2 mm)
12 kg fencing mask mesh
Modern rigid athletic cup
Perforated material that meets this requirement must have holes no larger than 1/8 inch (3 mm) in any direction, and a spacing of at least 3/16 inch (5 mm) center-to-center. In using these measurements, the perforated material must meet all the requirements of either the imperial or the metric units (or both).
Penetration resistant
Material that will predictably withstand puncture as demonstrated by passing a penetration test.
The following materials are known to pass these tests when new, but may be tested at the marshal's discretion;
4 ounce (1.6 mm) leather
Four layers of heavy poplin cloth
Ballistic nylon rated to at least 550 Newtons
Commercial fencing clothing rated to at least 550 Newtons
Chain mail made of welded or riveted steel rings that will not admit a 5/32 inch (4 mm) diameter probe. Rings no greater than 5/32 inch (4 mm) in internal diameter made of wire no less than 2/100 inch (0.5 mm) thick meets this requirement.
All other materials must be tested the first time new gear is used, or if no marshal on the field knows a given piece of gear to have been tested.
Penetration resistant armor (except chain mail) must be drop-tested at least every two years (see Inspecting equipment)
Penetration resistant armor may be tested at any time at the marshal's discretion using the drop tester. (see Inspecting equipment)
Chain mail armor meeting the definition of penetration resistant must not have more than one adjacent missing link. Missing links must be replaced before the armor is worn. Split rings with at least two full turns are acceptable replacement links.
Kevlar is not an acceptable material for penetration resistant armor.
UnderArmour, Spandex, and other similar stretchy materials are not suitable as puncture resistant materials and must not be included in the armor being testing.
Abrasion resistant
Material that will withstand normal combat stresses (such as being snagged by burr on a metal blade) without tearing.
Examples include, but are not limited to:
Broadcloth
A single layer of heavy poplin cloth (35% cotton, 65% polyester; "trigger" cloth)
Sweat pants
Opaque cotton, poly-cotton or lycra/spandex mix tights
Nylon pantyhose and cotton gauze shirts are examples of unacceptable materials.
Armor requirements for each area of the body
Head and neck
Face
Your face and the sides of your head to behind your ears must be covered by a 12kg fencing mask or equivalent head protection. Figure 4. The head and face, indicated here, must be protected by a 12 kg mask or equivalent.Figure 4 illustrates the portion of your face and head that must be protected by rigid material.
Your mask or helm must extend down past your chin so that your mask or helm and neck armor together do not leave a significant gap in the rigid protection that protects against typical thrusts coming from the front.
Your mask or helm must be secured, so that it cannot be easily removed or dislodged during combat.
All parts of your fencing mask or helm that might cause injurious contact with your head must be padded or be suspended in such a way as to prevent contact during combat.
There must be no major internal projections
Minor projections of necessary structural components must be padded.
All metal must be free of sharp edges.
Fencing masks
The interior of your fencing mask must have at least 1/4 inch (6 mm) open-cell foam or equivalent resilient padding to create separation between the mask and your face. Modern fencing masks (e.g. FIE and USFA type masks) in good working order meet this requirement without additional padding.
Your mask must be secured by a combination of the tongue/spring and the elastic back strap in good repair, or by the tongue/spring and other means such as a tie strap.
Helms
The metals listed under rigid armor are considered equivalent to a 12 kg fencing mask mesh.
If your helm uses a suspension system, it must prevent any rigid parts of your helm from contacting your head. At least 1/4 inch (6 mm) of open cell foam or equivalent resilient material may be used to meet this requirement.
If your helm does not have a suspension system and relies on foam, it must have at least 1/4 inch (6.4 mm) of closed-cell foam or equivalent resilient padding which provides progressive resistance to create separation between you and the hard outer shell of the helm.
If you have a movable visor, it must be attached and secured in such a way that there is minimal chance that it will become detached or come open in normal combat use.
Head
The rest of your head, aside from your face as defined above, must be covered by abrasion resistant material.
Neck
Figure 5. The parts of the neck shown here shaded must be covered by rigid protection. The double headed arrow indicates that the back of the neck to a total minimum width of 5 inches (125 mm) centered on the vertebrae must be covered.
The entire front 180 degrees of your neck, and at least 5 inches (125 mm) centered on your cervical vertebrae, must be covered by rigid material.
Gaps in rigid material at the sides beyond the front 180 degrees are allowed, but must be covered by puncture resistant material.
Body and groin armor
Your torso, including the abdomen down to and including the groin in front, and the inner arm down to 4 inches (10 cm) below the armpit, are to be covered by penetration resistant material.
If you have testicles, they must be protected by groin protection equivalent to that provided by an athletic cup, secured by straps, or worn in a supporter or garment designed to hold the protection in place.
Hand and wrist armor
Hands and wrists are not required to be covered.
Arm armor
The inner arm down to 4 inches (10 cm) below the armpit must be covered by penetration resistant material. The rest of the arm is not required to be covered.
General
Before rapier combat at each and every SCA event, including practices, training and pick-ups, a warranted rapier combat marshal must inspect and approve any armor you will use.
For multi-day events, you must have your armor inspected before each day's combat to check for any tears or signs of wearing.
Even though your armor and weapons have been inspected by a marshal, you accept full responsibility for the condition and safety of your equipment.
If you are a combatant on the field during rapier combat activities, you must wear armor that meets or exceeds the minimum standards set in this handbook, and any additional armor requirements of the kingdom you are in.
It is your responsibility to decide if you want to wear any additional armor beyond the minimum standards required, to reduce the risk of combat to an acceptable level to you.
Protection can come from a combination of armor and equipment, but must meet or exceed the minimum standards required.
The areas required to be armored must stay protected during typical movements that you will make during combat.
Your armor must be fastened in a way that prevents it from being dislodged in normal use.
All metal must be free of sharp edges.
You must disguise, cover, or remove modern corporate logos and sport gear unless the gear is necessary for medical reasons. We are trying to maintain the historical atmosphere.
If you have any body-worn medical equipment, you must cover it in such a way that it is protected against blows or the possibility of you falling on it if such an impact could damage it or cause injury.
Protective gear for marshals
If you are on the field, such as supervising combat, heralding etc., when missile weapons are present (e.g. combat archery, rubber band guns) you must wear eye protection which is sufficient to protect against the missiles in use. Examples include:
Industrial or sports safety glasses or goggles meeting the ANSI Z87.1 standard or better,
A fencing mask,
A helm that meets the standards for rapier combat.
